Honda CR/CRF Dress Up Kit (Nickel Würks)

$79.99 $64.99
(You save $15.00)
(2 reviews) Write a Review

Honda CR/CRF Dress Up Bolt Kit (Nickel Würks)

Configured to bring your HONDA CR to WÜRKS status using only the best fasteners. This kit uses 10.9 grade nickel plated fasteners. They are all designed with performance in mind. 

This high quality Nickel Würks bolt kit is for
Honda CR60, CR80, CR85, CR85, expert CR125, CR250 & CR500 (90's to current)
Honda CRF150R CRF250R & CRF450R (90's to current)


  • 6 Nickel Fork Guard bolts
  • 6 Nickel M5 shouldered radiator shroud bolts
  • 3 Sets of Nickel seat bolts
  • 2 correct square nuts for rear fender
  • Full Nickel Sprocket bolt kit... plastics, fender, body bolts and fender washers
  • Most visible engine side cover bolts
  • Radiator bolts
  • Shifter bolt
  • Flange Nuts for cylinder and head
  • Exhaust bolts
  • Most triple clamp and handlebar clamp bolts
  • Front axle pinch bolts
  • Front brake caliper bolts
  • Fuel tank bolts
  • Clutch and front brake perch bolts
  • Number plate and side panel bolts

...all with a hard and beautiful nickel finish.

More Information:

M6 Nickel Würks flange bolts in this kit range in size from M6x10 up to M6x45 and look beautiful used on your engine covers and plastics.

M8 Nickel Würks flange bolts in this kit range in size from M8x12 up to M8x45 and are perfect to replace your old bolts on your seat, front end, triple-clamps, bar mounts, axle pinch bolts, brake caliper mounts etc...

M6 Nickel Würks wide head flange bolts in this kit in 2 sizes. M6x12 & M6x16 are great for mounting radiator shrouds and bodywork plastics.

Our Specbolt drilled washers are perfect size and for mounting plastics and bodywork.

This kit contains a full assortment of Nickel Plated Flange nuts in M6, M8, and M10 sizes.

An assortment of the most needed Fender and Flat Washers are included.

A Full set of Nickel Würks Honda Sprocket Bolts with thread lock pre-applied. Complete with matching flat washers and class 10 flange bolts.

A full set of 6 Honda specific Fork Guard Bolts are included in the set. A big improvement over stock. They have been re-engineered to hold the fork guards a little tighter in place and eliminate any wiggle found on some models. This is especially helpful when running a holeshot device.

Powered byEMF Contact Form


2 Reviews Hide Reviews Show Reviews

  • 5
    Nickel wurks Honda CR bolt kit

    Posted by Scott Miner on Jul 7th 2020

    I bought this kit for an 07CR125 that I purchased, the nickel plated bolts look amazing and match up with all the stock bolt sizes. I put a 2020 restyle kit on the bike and this bolt kit helped make the bike look that much better!
    I know a lot of people believe that if it doesn’t make it stop or accelerate quicker then it shouldn’t be on the bike, I believe it’s worth every penny especially when freshening up an older bike.
    I also have to mention that customer service at spec bolt is second to none!

  • 4
    Great quality bolts, but my container was smashed when I got it. No big deal tho. Also it’s a little difficult figuring out what bolts go where. For example, the fork pinch bolts and front axle pinch bolts took some trial and error to see which worke

    Posted by Timmy Steinert on Feb 14th 2019

    Great bolts but hard to see which went where at times